This article below about How to Install a Bathtub Yourself is especially intriguing. Check it out for your own benefit and decide what you think about it.
Setting up a tub isn't exactly rocket science, yet it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately hard job. If the old tub is readily obtainable, the job can move speedily; if you have to open a wall surface to eliminate the old tub and also position the new bath tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will need a helper to vacate the old tub and also set in the new one. Make certain you have certified yourself for the job and also are comfortable trying it. Instead of working with a specialist to take over a halfway-completed task, it is much better to take into consideration employing one prior to you start. Possibilities are you might require an expert plumber to make tube links.
This article will aid you install a new bath tub in your bathroom if you have actually already gotten a brand-new tub as well as do not need to alter the setup of your previous water supply pipes.
Your devices and also material checklist must consist of the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing taps can be rather troublesome because of the limited accessibility that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the remaining water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washers remain in location between the tap and also the sink. Safeguard the tap in place with the manufacturer given backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former kind must be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bathtub
Making use of both wooden boards under its feet, position the tub in the required placement. The wooden boards are helpful in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 little points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub up until the spirit level checks out level.
To mount taps, fit all-time low of the furthest adaptable tap connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water system and examine all joints and brand-new pipework for leaks and also tighten them if needed. Fill the tub as well as also examine the overflow outlet as well as the regular outlet for leakages.
Finally, take care of the bath paneling as explained in the maker's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has actually been made use of at the very least once as this will settle it right into its last placement.
Planning for the Installation
First of all, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to ensure that if the faucet features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets device to prevent strain on the tub.
Fit the adaptable faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last setting.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, triggering the water to penetrate the wall surface in between the bath as well as the tiling, resulting in problems with dampness and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly load the bathtub with water prior to sealing, to allow for the motion experienced when the tub remains in use. The sealer can break fairly very early if you do not consider this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been introduced to that editorial on A Step-by-Step Guide to Installing a Bathtub through a friend on our other web property. Sharing is nice. Helping people is fun. I value reading our article about How to Install a Bathtub Yourself.
View More